# Глобальный конфигурационный файл Postfix'a. Этот файл описывает
# большинство всех параметр. Для изучения ситаксиса и получения списка 
# параметров, смотри postconf(5) (комманда: man 5 postconf)
# 
# Для общих конфигурационных примеров, смотри BASIC_CONFIGURATION_README
# и STANDARD_CONFIGURATION_README. Чтобы найти эти документы используй
# сомманду "postconf html_directory readme_directory", или посети
# http://www.postfix.org/.
#
# Для достижения лучших результатов изменяй не более 2-3 параметров
# за один раз и тестируй если postfix работает после каждого изменения.

# параметр обеспечивает ограниченную систему поддержки для тестирования. 
# Когда soft_bounce будет включен, почта останется поставленной в очередь,
# хотя должна была быть отклонена системой. 
# Этот параметр отключает локально-сгенерированные отключения(срывы,возвраты) 
# и препятствует тому, чтобы сервер SMTP отклонил почту надолго 
# (преобразую 5xx ответы в 4xx ответы). Однако, soft_bounce, не исправляет
# ошибки перезаписи адресов или маршрутизации почты.
#soft_bounce = no

###############################################################
# 1. ИНФОРМАЦИЯ О МЕСТЕ РАСПОЛОЖЕНИЯ
###############################################################
# определяет местоположение очереди. Это - также корневой каталог 
# демонов, которые выполняют работу в изолированой среде. Читают
# файлы в examples/chroot-setup для того, чтобы установить postfix 
# chroot среды на различных системах UNIX.
queue_directory = /var/spool/postfix
# там содержутся каталоги:
# -------------------------
# ls -1F /var/spool/postfix
# -------------------------
# active/ 
# bounce/ 
# corrupt/
# defer/
# deferred/
# flush/
# hold/
# incoming/
# maildrop/
# pid/
# private/
# public/
# saved/
# trace/
# -------------------------

# Директория комманд post***
command_directory = /usr/local/sbin
# ----------------------------------
# ls -1 /usr/local/sbin/ | grep post
# ----------------------------------
# postalias
# postcat
# postconf
# postdrop
# postfix
# postkick
# postlock
# postlog
# postmap
# postqueue
# postsuper
# ----------------------------------

# параметр определяет местоположение postfix'a и 
# программ-демонов (перечисленный в master.cf файле).
# этот каталог для демонов должен быть корневым.
daemon_directory = /usr/local/libexec/postfix
# -------------------------------------------
# ls -1
# -------------------------------------------
# anvil
# bounce
# cleanup
# discard
# error
# flush
# lmtp
# local
# master
# nqmgr
# oqmgr
# pickup
# pipe
# proxymap
# qmgr
# qmqpd
# scache
# showq
# smtp
# smtpd
# spawn
# tlsmgr
# trivial-rewrite
# verify
# virtual
# -------------------------------------------

###############################################################
# 2. ПРЕНАДЛЕЖНОСТЬ ПРОЦЕССОВ И ПОЧТОВОЙ ОЧЕРЕДИ
###############################################################
# параметр определяет владельца очереди и большинства процессов 
# демона. Определите имя пользователя. Ей будет учетная запись, 
# КОТОРАЯ НЕ РАЗДЕЛЯЕТ ПОЛЬЗОВАТЕЛЯ ИЛИ КОД ГРУППЫ С ДРУГИМИ 
# УЧЕТНЫМИ ЗАПИСЯМИ И ЕЙ НЕ ПРИНАДЛЕЖАТ НИКАКИЕ ДРУГИЕ ФАЙЛЫ 
# ИЛИ ПРОЦЕССЫ В СИСТЕМЕ. В частности, не определяйте nobody 
# или daemon. 
# ПОЖАЛУЙСТА ИСПОЛЬЗУЙТЕ СПЕЦИАЛИЗИРОВАННОГО ПОЛЬЗОВАТЕЛЯ.
#
mail_owner = postfix

# параметр определяет права по умолчанию, используемые доступ 
# к внешнему файлу или команде. НЕ ОПРЕДЕЛЯЙТЕ ПРИВИЛЕГИРОВАННОГО 
# ПОЛЬЗОВАТЕЛЯ ИЛИ ВЛАДЕЛЬЦА POSTFIX.
#
default_privs = nobody

###############################################################
# 3. ИНТЕРНЕТ ХОСТ И ИМЕНА ДОМЕНОВ
###############################################################
# параметр определяет имя хоста в интеренете этой почтовой
# системы. По умолчанию используется полное доменное имя 
# возвращаемое функцией gethostname(). Переменная $myhostname
# используется как значение по умолчанию для большенства других
# конфигурационных параметров
#
#myhostname = host.domain.tld
#myhostname = virtual.domain.tld

# параметр определяет локальное интеренет-имя домена.
# По умолчанию используется $myhostname минус первая часть имени.
# Переменная $mydomain используется как значение по умолчанию для 
# большенства других конфигурационных параметров.
#
#mydomain = domain.tld

###############################################################
# 4. ПОСЫЛКА(ОТПРАВКА) ПОЧТЫ
############################################################### 
# параметр определяет домен от которого почта исходит. По умолчанию 
# добавляется переменная $myhostname, необходимая маленьким сайтам
# (Т.е. адрес user@ + $myhostname = user@host.domain.tld)
# Здесь мы использовали это: myorigin = $myhostname
#
# Если используется несколько машин в одном домене, нужно:
# (1) именить $myadomain 
# (2) установить для всего домена базу данных алиасов
# (Т.е. адрес user@ + $mydomain = user@domain.tld)
# Здесь мы использовали это: myorigin = $mydomain
#
# Для соответствия между адресами отправителя и получателя, 
# myorigin также определяет заданное по умолчанию имя домена, 
# которое приложено к адресам получателя, у которых нет никакой 
# @domain части.
#
#myorigin = $myhostname
#myorigin = $mydomain

###############################################################
# 5. ПОЛУЧЕНИЕ ПОЧТЫ
###############################################################
# параметр определяет адрес сетевого интерфейса на которые эта 
# почтовая система будет получать почту. По умолчанию 
# программа "слушает" все активные интерфейсы на этой машине. 
# Этот параметр также сконтролирует доставку (поставку) почты 
# на user@[ip.adderss]
#
# Смотрите также параметр proxy_interfaces, для сетевых 
# адресов которые отправлены нам через proxy или через транслятор
# сетевого адреса (NAT)
#
# !!!: Для применения этих изменений нужно сделать stop/start
#
#inet_interfaces = all
#inet_interfaces = $myhostname
#inet_interfaces = $myhostname, localhost

# параметр определяет адрес сетевого интерфейса на которых эта
# почтовая система будет получать почту через proxy или через
# модуль трансляции сетевого адреса. Эти настройки расширяют
# список адресов определённых в параметре inet_interfaces
#
# Ты можешь определить твои proxy/NAT адреса, где твоя система
# будет резервным MX-хостом для другого домена, иначе снижаются
# шансы в доставке почты если первичный(главный) MX-хост выключен.
#
#proxy_interfaces =
#proxy_interfaces = 1.2.3.4

# параметр определяет список доменов для которых эта машина считает 
# себя конечным адресатом.
#
# Эти домены направлены агенту доставки, настройки кторого определены 
# в local_transport. По умолчанию, это UNIX-совместимый агент доставки
# просматривает всех получателей в /etc/passwd и /etc/aliases или их
# эквивалент.
#
# По умолчанию это $myhostname + localhost.$mydomain. На почтовом шлюзе 
# домена, ты должен так же включить $mydomain
#
# Не определяйте имена виртуальных доменов, так как виртуальные домены 
# определены в другом месте (смотри VIRTUAL_README).
#
# Не определяйте имена доменов для которых эта машины является резервным 
# MX-хост'ом. Определите их имена в настройках relay_domains для SMTP 
# сервера, или используйте permit_mx_backup если вам лень (смотри
# STANDARD_CONFIGURATION_README).
#
# Локальная машина всегда конечный адресат для адресованой почты для
# user@[the.net.work.address] на интерфейсе на котором получает почту
# почтовая система (смотри параметры inet_interfaces).
#
# Определи список хостов и доменных имён, /file/name или type:table
# шаблоны, разделённые and/or свободны местом (типа tab или space).
# /file/name - шаблон заменён его описанием; type:table согласован,
# когда название соответствует клавише поиска (правая сторона 
# проигнорирована). Продолжить длинную строку можно начав следущую 
# строку со свободного места.
#
# Cмотри также секцию ""
# See also below, section "REJECTING MAIL FOR UNKNOWN LOCAL USERS".
#
mydestination = $myhostname, localhost.$mydomain, localhost
#mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain
#mydestination = $myhostname, localhost.$mydomain, localhost, $mydomain,
#	mail.$mydomain, www.$mydomain, ftp.$mydomain

# REJECTING MAIL FOR UNKNOWN LOCAL USERS
#
# The local_recipient_maps parameter specifies optional lookup tables
# with all names or addresses of users that are local with respect
# to $mydestination, $inet_interfaces or $proxy_interfaces.
#
# If this parameter is defined, then the SMTP server will reject
# mail for unknown local users. This parameter is defined by default.
#
# To turn off local recipient checking in the SMTP server, specify
# local_recipient_maps = (i.e. empty).
#
# The default setting assumes that you use the default Postfix local
# delivery agent for local delivery. You need to update the
# local_recipient_maps setting if:
#
# - You define $mydestination domain recipients in files other than
#   /etc/passwd, /etc/aliases, or the $virtual_alias_maps files.
#   For example, you define $mydestination domain recipients in    
#   the $virtual_mailbox_maps files.
#
# - You redefine the local delivery agent in master.cf.
#
# - You redefine the "local_transport" setting in main.cf.
#
# - You use the "luser_relay", "mailbox_transport", or "fallback_transport"
#   feature of the Postfix local delivery agent (see local(8)).
#
# Details are described in the LOCAL_RECIPIENT_README file.
#
# Beware: if the Postfix SMTP server runs chrooted, you probably have
# to access the passwd file via the proxymap service, in order to
# overcome chroot restrictions. The alternative, having a copy of
# the system passwd file in the chroot jail is just not practical.
#
# The right-hand side of the lookup tables is conveniently ignored.
# In the left-hand side, specify a bare username, an @domain.tld
# wild-card, or specify a user@domain.tld address.
# 
local_recipient_maps = unix:passwd.byname $alias_maps
#local_recipient_maps = proxy:unix:passwd.byname $alias_maps
#local_recipient_maps =

# The unknown_local_recipient_reject_code specifies the SMTP server
# response code when a recipient domain matches $mydestination or
# ${proxy,inet}_interfaces, while $local_recipient_maps is non-empty
# and the recipient address or address local-part is not found.
#
# The default setting is 550 (reject mail) but it is safer to start
# with 450 (try again later) until you are certain that your
# local_recipient_maps settings are OK.
#
unknown_local_recipient_reject_code = 550

# TRUST AND RELAY CONTROL

# The mynetworks parameter specifies the list of "trusted" SMTP
# clients that have more privileges than "strangers".
#
# In particular, "trusted" SMTP clients are allowed to relay mail
# through Postfix.  See the smtpd_recipient_restrictions parameter
# in postconf(5).
#
# You can specify the list of "trusted" network addresses by hand
# or you can let Postfix do it for you (which is the default).
#
# By default (mynetworks_style = subnet), Postfix "trusts" SMTP
# clients in the same IP subnetworks as the local machine.
# On Linux, this does works correctly only with interfaces specified
# with the "ifconfig" command.
# 
# Specify "mynetworks_style = class" when Postfix should "trust" SMTP
# clients in the same IP class A/B/C networks as the local machine.
# Don't do this with a dialup site - it would cause Postfix to "trust"
# your entire provider's network.  Instead, specify an explicit
# mynetworks list by hand, as described below.
#  
# Specify "mynetworks_style = host" when Postfix should "trust"
# only the local machine.
# 
#mynetworks_style = class
#mynetworks_style = subnet
mynetworks_style = host

# Alternatively, you can specify the mynetworks list by hand, in
# which case Postfix ignores the mynetworks_style setting.
#
# Specify an explicit list of network/netmask patterns, where the
# mask specifies the number of bits in the network part of a host
# address.
#
# You can also specify the absolute pathname of a pattern file instead
# of listing the patterns here. Specify type:table for table-based lookups
# (the value on the table right-hand side is not used).
#
mynetworks = 192.168.0.0/16, 127.0.0.0/8
#mynetworks = $config_directory/mynetworks
#mynetworks = hash:/usr/local/etc/postfix/network_table

# The relay_domains parameter restricts what destinations this system will
# relay mail to.  See the smtpd_recipient_restrictions description in
# postconf(5) for detailed information.
#
# By default, Postfix relays mail
# - from "trusted" clients (IP address matches $mynetworks) to any destination,
# - from "untrusted" clients to destinations that match $relay_domains or
#   subdomains thereof, except addresses with sender-specified routing.
# The default relay_domains value is $mydestination.
# 
# In addition to the above, the Postfix SMTP server by default accepts mail
# that Postfix is final destination for:
# - destinations that match $inet_interfaces or $proxy_interfaces,
# - destinations that match $mydestination
# - destinations that match $virtual_alias_domains,
# - destinations that match $virtual_mailbox_domains.
# These destinations do not need to be listed in $relay_domains.
# 
# Specify a list of hosts or domains, /file/name patterns or type:name
# lookup tables, separated by commas and/or whitespace.  Continue
# long lines by starting the next line with whitespace. A file name
# is replaced by its contents; a type:name table is matched when a
# (parent) domain appears as lookup key.
#
# NOTE: Postfix will not automatically forward mail for domains that
# list this system as their primary or backup MX host. See the
# permit_mx_backup restriction description in postconf(5).
#
relay_domains = $mydestination

# INTERNET OR INTRANET

# The relayhost parameter specifies the default host to send mail to
# when no entry is matched in the optional transport(5) table. When
# no relayhost is given, mail is routed directly to the destination.
#
# On an intranet, specify the organizational domain name. If your
# internal DNS uses no MX records, specify the name of the intranet
# gateway host instead.
#
# In the case of SMTP, specify a domain, host, host:port, [host]:port,
# [address] or [address]:port; the form [host] turns off MX lookups.
#
# If you're connected via UUCP, see also the default_transport parameter.
#
#relayhost = $mydomain
#relayhost = [gateway.my.domain]
#relayhost = [mailserver.isp.tld]
#relayhost = uucphost
#relayhost = [an.ip.add.ress]

# REJECTING UNKNOWN RELAY USERS
#
# The relay_recipient_maps parameter specifies optional lookup tables
# with all addresses in the domains that match $relay_domains.
#
# If this parameter is defined, then the SMTP server will reject
# mail for unknown relay users. This feature is off by default.
#
# The right-hand side of the lookup tables is conveniently ignored.
# In the left-hand side, specify an @domain.tld wild-card, or specify
# a user@domain.tld address.
# 
#relay_recipient_maps = hash:/usr/local/etc/postfix/relay_recipients

# INPUT RATE CONTROL
#
# The in_flow_delay configuration parameter implements mail input
# flow control. This feature is turned on by default, although it
# still needs further development (it's disabled on SCO UNIX due
# to an SCO bug).
# 
# A Postfix process will pause for $in_flow_delay seconds before
# accepting a new message, when the message arrival rate exceeds the
# message delivery rate. With the default 100 SMTP server process
# limit, this limits the mail inflow to 100 messages a second more
# than the number of messages delivered per second.
# 
# Specify 0 to disable the feature. Valid delays are 0..10.
# 
#in_flow_delay = 1s

# ADDRESS REWRITING
#
# The ADDRESS_REWRITING_README document gives information about
# address masquerading or other forms of address rewriting including
# username->Firstname.Lastname mapping.

# ADDRESS REDIRECTION (VIRTUAL DOMAIN)
#
# The VIRTUAL_README document gives information about the many forms
# of domain hosting that Postfix supports.

# "USER HAS MOVED" BOUNCE MESSAGES
#
# See the discussion in the ADDRESS_REWRITING_README document.

# TRANSPORT MAP
#
# See the discussion in the ADDRESS_REWRITING_README document.

# ALIAS DATABASE
#
# The alias_maps parameter specifies the list of alias databases used
# by the local delivery agent. The default list is system dependent.
#
# On systems with NIS, the default is to search the local alias
# database, then the NIS alias database. See aliases(5) for syntax
# details.
# 
# If you change the alias database, run "postalias /etc/aliases" (or
# wherever your system stores the mail alias file), or simply run
# "newaliases" to build the necessary DBM or DB file.
#
# It will take a minute or so before changes become visible.  Use
# "postfix reload" to eliminate the delay.
#
#alias_maps = dbm:/etc/aliases
#alias_maps = hash:/etc/aliases
#alias_maps = hash:/etc/aliases, nis:mail.aliases
#alias_maps = netinfo:/aliases

# The alias_database parameter specifies the alias database(s) that
# are built with "newaliases" or "sendmail -bi".  This is a separate
# configuration parameter, because alias_maps (see above) may specify
# tables that are not necessarily all under control by Postfix.
#
#alias_database = dbm:/etc/aliases
#alias_database = dbm:/etc/mail/aliases
#alias_database = hash:/etc/aliases
#alias_database = hash:/etc/aliases, hash:/opt/majordomo/aliases

# ADDRESS EXTENSIONS (e.g., user+foo)
#
# The recipient_delimiter parameter specifies the separator between
# user names and address extensions (user+foo). See canonical(5),
# local(8), relocated(5) and virtual(5) for the effects this has on
# aliases, canonical, virtual, relocated and .forward file lookups.
# Basically, the software tries user+foo and .forward+foo before
# trying user and .forward.
#
#recipient_delimiter = +

# DELIVERY TO MAILBOX
#
# The home_mailbox parameter specifies the optional pathname of a
# mailbox file relative to a user's home directory. The default
# mailbox file is /var/spool/mail/user or /var/mail/user.  Specify
# "Maildir/" for qmail-style delivery (the / is required).
#
#home_mailbox = Mailbox
#home_mailbox = Maildir/
 
# The mail_spool_directory parameter specifies the directory where
# UNIX-style mailboxes are kept. The default setting depends on the
# system type.
#
#mail_spool_directory = /var/mail
#mail_spool_directory = /var/spool/mail

# The mailbox_command parameter specifies the optional external
# command to use instead of mailbox delivery. The command is run as
# the recipient with proper HOME, SHELL and LOGNAME environment settings.
# Exception:  delivery for root is done as $default_user.
#
# Other environment variables of interest: USER (recipient username),
# EXTENSION (address extension), DOMAIN (domain part of address),
# and LOCAL (the address localpart).
#
# Unlike other Postfix configuration parameters, the mailbox_command
# parameter is not subjected to $parameter substitutions. This is to
# make it easier to specify shell syntax (see example below).
#
# Avoid shell meta characters because they will force Postfix to run
# an expensive shell process. Procmail alone is expensive enough.
#
# IF YOU USE THIS TO DELIVER MAIL SYSTEM-WIDE, YOU MUST SET UP AN
# ALIAS THAT FORWARDS MAIL FOR ROOT TO A REAL USER.
#
#mailbox_command = /some/where/procmail
#mailbox_command = /some/where/procmail -a "$EXTENSION"

# The mailbox_transport specifies the optional transport in master.cf
# to use after processing aliases and .forward files. This parameter
# has precedence over the mailbox_command, fallback_transport and
# luser_relay parameters.
#
# Specify a string of the form transport:nexthop, where transport is
# the name of a mail delivery transport defined in master.cf.  The
# :nexthop part is optional. For more details see the sample transport
# configuration file.
#
# NOTE: if you use this feature for accounts not in the UNIX password
# file, then you must update the "local_recipient_maps" setting in
# the main.cf file, otherwise the SMTP server will reject mail for    
# non-UNIX accounts with "User unknown in local recipient table".
#
#mailbox_transport = lmtp:unix:/file/name
#mailbox_transport = cyrus

# The fallback_transport specifies the optional transport in master.cf
# to use for recipients that are not found in the UNIX passwd database.
# This parameter has precedence over the luser_relay parameter.
#
# Specify a string of the form transport:nexthop, where transport is
# the name of a mail delivery transport defined in master.cf.  The
# :nexthop part is optional. For more details see the sample transport
# configuration file.
#
# NOTE: if you use this feature for accounts not in the UNIX password
# file, then you must update the "local_recipient_maps" setting in
# the main.cf file, otherwise the SMTP server will reject mail for    
# non-UNIX accounts with "User unknown in local recipient table".
#
#fallback_transport = lmtp:unix:/file/name
#fallback_transport = cyrus
#fallback_transport =

# The luser_relay parameter specifies an optional destination address
# for unknown recipients.  By default, mail for unknown@$mydestination,
# unknown@[$inet_interfaces] or unknown@[$proxy_interfaces] is returned
# as undeliverable.
#
# The following expansions are done on luser_relay: $user (recipient
# username), $shell (recipient shell), $home (recipient home directory),
# $recipient (full recipient address), $extension (recipient address
# extension), $domain (recipient domain), $local (entire recipient
# localpart), $recipient_delimiter. Specify ${name?value} or
# ${name:value} to expand value only when $name does (does not) exist.
#
# luser_relay works only for the default Postfix local delivery agent.
#
# NOTE: if you use this feature for accounts not in the UNIX password
# file, then you must specify "local_recipient_maps =" (i.e. empty) in
# the main.cf file, otherwise the SMTP server will reject mail for    
# non-UNIX accounts with "User unknown in local recipient table".
#
#luser_relay = $user@other.host
#luser_relay = $local@other.host
#luser_relay = admin+$local
  
# JUNK MAIL CONTROLS
# 
# The controls listed here are only a very small subset. The file
# SMTPD_ACCESS_README provides an overview.

# The header_checks parameter specifies an optional table with patterns
# that each logical message header is matched against, including
# headers that span multiple physical lines.
#
# By default, these patterns also apply to MIME headers and to the
# headers of attached messages. With older Postfix versions, MIME and
# attached message headers were treated as body text.
#
# For details, see "man header_checks".
#
#header_checks = regexp:/usr/local/etc/postfix/header_checks

# FAST ETRN SERVICE
#
# Postfix maintains per-destination logfiles with information about
# deferred mail, so that mail can be flushed quickly with the SMTP
# "ETRN domain.tld" command, or by executing "sendmail -qRdomain.tld".
# See the ETRN_README document for a detailed description.
# 
# The fast_flush_domains parameter controls what destinations are
# eligible for this service. By default, they are all domains that
# this server is willing to relay mail to.
# 
#fast_flush_domains = $relay_domains

# SHOW SOFTWARE VERSION OR NOT
#
# The smtpd_banner parameter specifies the text that follows the 220
# code in the SMTP server's greeting banner. Some people like to see
# the mail version advertised. By default, Postfix shows no version.
#
# You MUST specify $myhostname at the start of the text. That is an
# RFC requirement. Postfix itself does not care.
#
#smtpd_banner = $myhostname ESMTP $mail_name
#smtpd_banner = $myhostname ESMTP $mail_name ($mail_version)

# PARALLEL DELIVERY TO THE SAME DESTINATION
#
# How many parallel deliveries to the same user or domain? With local
# delivery, it does not make sense to do massively parallel delivery
# to the same user, because mailbox updates must happen sequentially,
# and expensive pipelines in .forward files can cause disasters when
# too many are run at the same time. With SMTP deliveries, 10
# simultaneous connections to the same domain could be sufficient to
# raise eyebrows.
# 
# Each message delivery transport has its XXX_destination_concurrency_limit
# parameter.  The default is $default_destination_concurrency_limit for
# most delivery transports. For the local delivery agent the default is 2.

#local_destination_concurrency_limit = 2
#default_destination_concurrency_limit = 20

# DEBUGGING CONTROL
#
# The debug_peer_level parameter specifies the increment in verbose
# logging level when an SMTP client or server host name or address
# matches a pattern in the debug_peer_list parameter.
#
debug_peer_level = 2

# The debug_peer_list parameter specifies an optional list of domain
# or network patterns, /file/name patterns or type:name tables. When
# an SMTP client or server host name or address matches a pattern,
# increase the verbose logging level by the amount specified in the
# debug_peer_level parameter.
#
#debug_peer_list = 127.0.0.1
#debug_peer_list = some.domain

# The debugger_command specifies the external command that is executed
# when a Postfix daemon program is run with the -D option.
#
# Use "command .. & sleep 5" so that the debugger can attach before
# the process marches on. If you use an X-based debugger, be sure to
# set up your XAUTHORITY environment variable before starting Postfix.
#
debugger_command =
	 PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin
	 xxgdb $daemon_directory/$process_name $process_id & sleep 5

# If you can't use X, use this to capture the call stack when a
# daemon crashes. The result is in a file in the configuration
# directory, and is named after the process name and the process ID.
#
# debugger_command =
#	PATH=/bin:/usr/bin:/usr/local/bin; export PATH; (echo cont;
#	echo where) | gdb $daemon_directory/$process_name $process_id 2>&1
#	>$config_directory/$process_name.$process_id.log & sleep 5
#
# Another possibility is to run gdb under a detached screen session.
# To attach to the screen sesssion, su root and run "screen -r
# " where  uniquely matches one of the detached
# sessions (from "screen -list").
#
# debugger_command =
#	PATH=/bin:/usr/bin:/sbin:/usr/sbin; export PATH; screen
#	-dmS $process_name gdb $daemon_directory/$process_name
#	$process_id & sleep 1

# INSTALL-TIME CONFIGURATION INFORMATION
#
# The following parameters are used when installing a new Postfix version.
# 
# sendmail_path: The full pathname of the Postfix sendmail command.
# This is the Sendmail-compatible mail posting interface.
# 
sendmail_path = /usr/local/sbin/sendmail

# newaliases_path: The full pathname of the Postfix newaliases command.
# This is the Sendmail-compatible command to build alias databases.
#
newaliases_path = /usr/local/bin/newaliases

# mailq_path: The full pathname of the Postfix mailq command.  This
# is the Sendmail-compatible mail queue listing command.
# 
mailq_path = /usr/local/bin/mailq

# setgid_group: The group for mail submission and queue management
# commands.  This must be a group name with a numerical group ID that
# is not shared with other accounts, not even with the Postfix account.
#
setgid_group = maildrop

html_directory = no
manpage_directory = /usr/local/man
sample_directory = /usr/local/etc/postfix
readme_directory = no

# alwais 
# recipient - получатель
# destination - адресат
# pattern - шаблон